Take the 2-minute tour ×
Musical Practice & Performance Stack Exchange is a question and answer site for musicians, students, and enthusiasts. It's 100% free, no registration required.

I've a lot of people using a pre amp pedal. What does that pedal do?

Do I need one on my pedalboard?

share|improve this question

2 Answers 2

up vote 5 down vote accepted

A pre-amp amplifies a quiet signal such as that from a passive guitar pickup, or a microphone, into a louder signal suitable for the input of a power amplifier.

A couple of terms:

  • "Instrument level" - the signal strength that typically comes out of a pickup instrument. This is generally so weak that if you connected it direct to some headphones, you wouldn't hear anything. It is literally the amount of energy generated by a vibrating string near a magnet.

  • "Line level" - a standard signal strength for sending unbalanced signals between audio components. It's what's meant when you see "line in" or "line out" on sockets on audio equipment. This is powerful enough that if you connected it direct to headphones, you'd generally hear a loud, clear sound. This level is chosen because it's quiet enough to be produced by small electronic components, but loud enough to drown out interference noise for short distances.

Some guitar amps contain their own preamp, or at least are capable of sounding good with an instrument level input. But some amplifiers need line level input to get any kind of useful sound. Additionally a preamp can be an effective way of overdriving an amp, where the instrument alone wouldn't have enough power.

You also encounter preamps in the world of HiFi, where they are used to bring the signal from a turntable up to the level required by the main amp.

Different preamps have different design goals. Some are designed to amplify the sound as accurately as possible. Other preamps are intended to colour the sound and add their own character.

You may have a pre-amp already, and not know it. A lot of multi-FX pedals accept instrument-level inputs, but output at line-level.

share|improve this answer
1  
In the guitar world, would this be the same as a DI box? –  NReilingh Dec 1 '13 at 20:35
1  
Not quite. A DI box turns an unbalanced signal into a balanced signal suitable for transmitting over long cable runs. –  slim Dec 1 '13 at 20:54
    
Ah, so typically that would come after your preamp in the signal chain, then. –  NReilingh Dec 1 '13 at 20:58
1  
Guitar - D.I - amp. would be the way, as the D.I. changes the signal to allow longer cables without loss. Often, particularly in guitar amps, the pre - and post are integral, sometimes split physically with a 'send/return'. As some D.I. are active, thus will have their own 'pre-amp', they can still go straight after the guitar, but don't necessarily need to go through another pre-amp in the guitar amp. A lot of pedalboards contain a pre-amp section. –  Tim Dec 2 '13 at 9:03
1  
@slim - with a 'big-gig' set-up, there would probably be no need to d.i. box the mic., as it would (usually) be low impedance, thus long cable runs would be no problem. From the guitar amp., you could use a d.i. box instead of the mic, to take the signal straight to the mixer/p.a. –  Tim Dec 2 '13 at 10:26

Every pedal in your pedalboard already incorporates a preamp, or can be regarded as one. An overdrive pedal is a preamp. A distortion pedal is a preamp. A chorus pedal is a preamp. En equalizer pedal is a preamp.

All of these boxes are designed such that any of them can be the first element in your signal chain right after the instrument, dealing with the weak signal from a passive pickup. Even the ones that do not provide a level boost still boost the signal's current driving ability: the devices can drive a lower impedance load (such as a line level input) than your guitar is able to. They meet any reasonable definition of the word preamp.

So for instance if all you have is a guitar, amp and a 10 band equalizer stomp-box, plus a pair of cables, you have a preamp. You should be able to plug into the box, from that patch into the power amp, and play with reasonably good sound. This setup is very similar to going through the clean channel of a guitar amplifier.

When people tell you that they have a pre-amp in their pedalboard or that you should get one, they probably mean "guitar preamp".

"guitar preamp" is a kind of marketing word which refers to an electronic device that provides a more or less complete solution for taking the signal from a guitar and preparing a tone-shaped signal that is ready to go into a power-amp. Guitar pre-amps have features like switching between multiple channels that have independent settings, and integrate a lot more controls. Whereas a distortion pedal might have just a simple tone control and a switch for bypass, a preamp pedal might have a switch between two channels, and a more sophisticated EQ, and perhaps even a delay effect built in.

Basically it's just a more functionally integrated unit than regular pedals. For an example of a guitar pre-amp in a pedal format, look at, for instance, the ADA APP-1: a new item from a re-start of the same company that brought us the ADA MP-1 rackmount MIDI-controlled tube preamp in the late 1980's. What is this, really? It's something like having an A/B box, and several compression, distortion and EQ pedals rolled into one enclosure.

If you have this in your pedal board, chances are that some of your boxes become unnecessary and can be taken out.

share|improve this answer

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.