Take the 2-minute tour ×
Musical Practice & Performance Stack Exchange is a question and answer site for musicians, students, and enthusiasts. It's 100% free, no registration required.

I've read before that a Floyd Rose bridge should be parallel to the body of the guitar.

This is an image of the bridge on my guitar:

picture

You can see that the left side of the appears to be a little bit lower than the right. Is this correct? should the bridge be parallel?

If so, how can I go about correcting this? I have an extra spring that came with the guitar. Currently there are 3 springs in it, but I could get the extra one added. But I was under the impression that the extra spring was only for higher guage strings, and I have .9's on mine so I didn't think it would be necessary?

share|improve this question
    
3 springs is enough for .9s and flexible enough : you have to adjust the claw to adjust the position. More or less springs will affect the response (and IMO 2 is laughably soft, and probably a pain to keep in tune) –  Pif Feb 15 '11 at 10:10

3 Answers 3

The Floyd Rose bridge should be parallel with the body; if it is not, you will have to make major and unnecessary adjustments to the other parts of the guitar in order to get a good action and correct intonation/'overall set up' (which you will likely find hard with the bridge at that angle.).

The correct method to bring the bridge parallel is to adjust the spring plate which your bridge is attached to/floating on. (Using a spring instead is perfectly acceptable if it produces the required result and brings the bridge parallel with the body; you may find however that the spring provides too much or too little tension and that you still have to make spring plate adjustments).

This is done by adjusting the screws which attach the plate to the guitar. If you would like to increase the tension of the springs(lower the bridge), then you need to tighten the screws(bringing the plate closer to the body of the guitar).

This is needed if you increase the gauge of your strings, thus increasing the tension of the strings on the bridge. If you put smaller gauge strings on the guitar you will likely have to untighten the screws(move the plate further from the wood).

Any adjustment to the spring plate screws should be done a half/quarter turn at a time with the strings slackened; each time you make an adjustment you will need to retune the guitar and check the bridge.

This can be a tedious process, but i know from lifetime of using Floyd Rose equipped guitars that this effort is required to get the best out of the guitar. (Completely parallel might be a pain; as near as possible is good enough)

Assuming you intend to keep the same gauge strings on the guitar, once you have done this the first time, you shouldn't have to do it again when you change strings; unless something else major changes.

Edit: In your image - the distance of your strings from the pickup will also affect the tone of the guitar.

share|improve this answer
    
+1 I personally don't mind a- very - slight tilt, but I would definitely setup my whammy if it was like in that photo. It's a laborious bitch to do but it's not that otfen you have to. –  Pif Feb 15 '11 at 10:17

I don't think there's anything wrong with the bridge as you have it set up. Sure, you could set it up so that it's parallel with the body, but it's not necessary. It all depends on how you want to use the whammy bar. The more the bridge tilts forward, the more you can pull the whammy bar back and raise the pitch of the strings; conversely, the more it tilts backward, the more room you have to push the bar down and lower the pitch of the strings.

Jeff Beck, for example, has his bridge (which isn't a Floyd Rose, but still) tilted way far forward---much more so than yours---because he wants to be able to pull the bar back a lot. I guess you have to ask yourself, "I am a dive-bomber or am I a screamer?" Not that you can't be both, of course; it's just a question of degree.

If you decide you do want to adjust the tilt of the bridge after all, you have two options:

  1. You can add the extra spring. This will definitely do it---maybe too much, even---but it will also make the tremolo "stiffer", i.e. harder to whammy, if you will. That's good for staying in tune, but bad for actually using the whammy bar for its intended purpose.
  2. You can adjust the plate to which the springs are connected in the back of your guitar. Turn the guitar over on its belly and remove the rectangular plastic plate through which you thread your strings when you re-string the guitar. You'll see that the tremolo springs are attached to a metal plate. This plate is held in place by some screws that you can tighten or loosen. Tighten them and you'll raise the spring tension of your existing springs, which may be enough to pull your bridge back without having to add the extra spring. The only disadvantage of this approach is that you can only tighten the plate so far---once it's flush with the wood of the guitar, that's as tight as it gets.

So, again, I don't think you need to worry about this. But if you do want to lower the bridge to parallel, my advice would be to adjust the spring tension plate first and see if that does the trick, and only after that would I add the extra spring.

share|improve this answer
1  
But JB uses guitars that don't have a cutout for the bridge. It seems from the photo that pulling the whammy bar shouldn't be a problem if the block's parallel to the body. –  Pif Feb 15 '11 at 10:16
    
I have one guitar set up with the bridge far forwards, one with it far back and the others as horizontal as I could manage. This is mostly for the divebomb/scream options, but also give some nice tonal options. –  Dr Mayhem Feb 22 '11 at 15:02
    
I've had a Floyd not parallel to the body, and I've had issues : basically only one direction would go back to tuning. I've corrected the angle and everything is smooth (not to mention the overall action and pickup height are easier to set up). I'm not sure the Beck comparison is correct, for two reasons : 1 - a strat trem is quite different; 2 - the guy has a guitar tech. It's quite different if you have to set the whole thing up and take care of it yourself, especially if guitar playing is a hobby. –  Pif Mar 16 '12 at 10:00

Hi Dave (I guess that's your name), as you can tell from the answers you've already received, it's important that a Floyd-Rose-style tremolo is parallel to the body. The reason is that the knife-edge stays in the right degree to the carve in the pin/bolt. So that it will have the same pressure on the upper and under side of the carve. This is important for your tuning stability and the main reason why you should do that.

I made a graphic for you (and everyone that has the same question) that should be easier to understand than plain words:

Floyd placement

I hope that helps :) sincerely, Markus Schwalbe

share|improve this answer
    
Thanks Markus. This info is useful. I've decided that I'm going to bring the guitar into a specialist to do the job because it's just too easy for me to make a balls of it. –  Anonymous Apr 27 '11 at 14:57

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.